† Corresponding author. E-mail:
Project supported by the National Natural Science Foundation of China (Grant Nos. 91644107, 61575206, 51904009, and 41905130), the National Key Research and Development Program of China (Grant Nos. 2017YFC0209401, 2017YFC0209403, and 2017YFC0209902), and the Outstanding Young Talents Program of Anhui University, China (Grant No. gxyq2019022).
An NO2 photoacoustic sensor system with a high reflective mirror based on a low power blue diode laser is developed in this work. The excitation power is enhanced by increasing the number of reflections. Comparing with a traditional photoacoustic system, the pool constant is improved from 300.24 (Pa⋅cm)/W to 1450.64 (Pa⋅cm)/W, and the signal sensitivity of the photoacoustic sensor is increased from 0.016 μV/ppb to 0.2562 μV/ppb. The characteristics of temperature and humidity of the new photoacoustic sensor are also obtained, and the algorithm is adjusted to provide a quantitative response and drift of the resonance frequency. The results of this research provide a new method and concept for further developing the NO2 photoacoustic sensors.
Photoacoustic spectroscopy (PAS) is based on the photoacoustic effect. No radiation relaxation occurs when converting part or all of the absorbed light energy into heat. The resulting pressure wave then radiates outward. Gas detection refers to exploring the source of heat power density with periodic changes formed through the absorption and modulation of light energy by gas molecules in a closed cavity, thus causing the gas pressure to periodically change in the cavity and stimulating the sound signal. The cavity is generally considered to radiate ultrasonic pressure waves.[1,2] As an important detection technique for tracing gas, this technique is widely applied to atmospheric science.[1,3–13] When there is no problem of saturation, the response of photoacoustic spectroscopy is proportional to the excited laser power, and thus the photoacoustic performance can be improved by increasing the excited laser power. The commonly used methods mainly include two approaches: (i) a laser with higher power is used to increase the energy relaxation process. The high-power diode laser with 3.5 W is modulated to the mean output power of 1.5 W in the front of the photoacoustic cell by a square signal with a duty cycle of 50%, and is used to detect NO2 with a detection limit of 54 ppt (1 s).[3,4] However, due to the large beam diameter and divergence, the high-power diode laser without any specific optic treatment is unsuitable for the photoacoustic system with conventional cavity structures and is not compatible with existing cavity technology.[14–17] However, the low power blue diode laser with output power in a range of mW is widely used and is compatible with different detection technologies for the cavity structure with a small internal diameter.[18–23] (ii) The photoacoustic cell can be optimized to improve the power by increasing the number of reflections. When the photoacoustic spectroscopy is combined with the cavity-enhanced absorption spectroscopy, the power in the cavity will be improved.[24–29] However, related research has mainly focused on the infrared band, while research on the ultraviolet band has been quite limited.
In this manuscript, we describe a new NO2 photoacoustic sensor system with a high reflective mirror based on a low power blue diode laser at 403.56 nm, which can be used to optimize the photoacoustic cell. The power to excit the trace gas is enhanced through using the high reflective mirror to add a light path reflection. We design a photoacoustic cavity with a pool constant of 1450.64 (Pa⋅cm)/W and the signal sensitivity of 0.2562 μV/ppb. Comparing with a traditional photoacoustic system, the gain factor of the pool constant is 4.8, and the gain factor of signal sensitivity is 16. The temperature and humidity property of the new NO2 photoacoustic sensor are analyzed, and the photoacoustic response and the drift of resonance frequency are also obtained.
Since the absorption coefficient is equal to the product of the absorption cross section and the concentration, the effective influence of the absorption cross section and interfering gas should be taken into consideration when selecting the laser. The absorption cross section of NO2 for 390 nm–420 nm is shown in Fig.
The NO2 photoacoustic sensor with a high reflective mirror consists of a traditional photoacoustic cell, two buffer cavities with a gas inlet, and a gas outlet, a quartz glass plate, and a high reflective mirror. The schematic diagram of the sensor is shown in Fig.
In order to obtain the reflectivity of the high-reflectivity mirror and ensure laser alignment and experimental consistency, a pair of high reflective mirrors are selected for calibrating and testing the cavity ring-down system (CRDS) that is designed and developed by our research group as shown in Fig.
The system mainly depends on adjusting the ring down time of the cavity ring down system and observing the laser spots on the mirror to ensure the consistency of the light path of the series mode. In the series of optical paths, the photoacoustic cavity is outside of the ring down cavity and arranged independently, the photoacoustic cavity will be at the position to be passed through. It is actually sealed by the quartz window, the verticality of the quartz window needs adjusting during the system adjustment, and the ring down cavity needs adjusting to determine whether the series of optical paths is collimated by determining the maximum ring down time. The optical path collimation is also applicable to the adjustment method.
The resonance frequency of the photoacoustic cell with a high-reflectivity mirror in the atmospheric environment is experimentally determined to be f0 ≈ 1319.7 Hz and the full width at half maximum (FWHM) of the frequency response curve (Fig.
The experimental setup of the NO2 photoacoustic sensor with a high-reflectivity mirror is depicted in Fig.
The pure N2 and NO2 sample gases with 0.204 ppm are used as a mixed source gas. The mixed gases with different concentrations, water vapor, and temperatures are configured by controlling the flow rate and thermometer. The total flow should be controlled at 1 L/min by controlling the flow rate of the pure nitrogen, water vapor, and NO2. The heating device consists of a copper spiral tube, flexible silicone rubber heating tablets, high temperature insulation materials, a temperature probe, and temperature controllers. The length and diameter of the copper spiral tube are 30 cm and 6.5 cm respectively. The resistance and the power of the flexible silicone rubber heating tablets are 396 Ω and 120 W respectively. High temperature insulation materials consist of quartz fiber and cotton insulation. The experimental system test site is shown in Fig.
The background noise and excitation signal are tested with 3.4-ppm NO2. The background noise of the system is 3.212 ± 0.188 μV, compared with the excitation signal of 109.217 ± 1.043 μV. The data in this paper are all computed by subtracting the local noise. The specific background noise information is shown in Fig.
When the sensor is first filled with 0.204-ppm NO2, the signal value from the photoacoustic sensor is 26.11 μV. The measurements are carried out at atmospheric pressure and room temperature. The absorption cross section of NO2 is 5.9485× 10−19 cm2/mole, the sensitivity of the microphone is 53.7 mV/Pa, and the laser power is doubled to 112.4 mW by the high-relectivitiy mirror, so the pool constant of the photoacoustic cell can be calculated from the following equation:
In order to evaluate the performance of the sensor in terms of accuracy and linearity, seven different concentration levels of the NO2 sample gas ranging from 17 ppb to 340 ppb are fed into the sensor. The signal amplitudes from the sensor are shown in Fig.
The performance test of a traditional photoacoustic cell sealed by two quartz glass plates is conducted and the result is shown in Fig.
Standard NO2 gas is selected as the standard gas to be used in the experiment; its concentration is 0.34 ppm, and the humidity of the gas remains at 0%. The experiments are carried out at atmospheric pressure and room temperature. By comparison, the responsivity values of the photoacoustic sensor under temperatures ranging from 20.9 °C to 31.4 °C are shown in Fig.
In the same way the photoacoustic sensor is filled with the NO2 sample gas at a specific temperature and concentration. Similarly, the NO2 sample gases with various values of the humidity at a specific temperature fill the photoacoustic sensor, respectively, in experiments. By comparison the signals of the photoacoustic sensor under various values of the humidity ranging from 0% to 90% are shown in Fig.
In this paper, the neural network algorithm is introduced into the later data processing of the photoacoustic system, and the self-designed cavity ring down system is selected as the reference measurement system to carry out the research on the correction method of the influence of temperature and humidity on the photoacoustic system. The designed parameter data have three inputs and one output. The three inputs are light acoustic response, temperature, and humidity inputs. The one output is the true value output of the cavity attenuation system. A three-layered BP neural network is used to carry out the correction study, and the hidden layer node is set at 15.
The photoacoustic system and cavity ring down system are used to measure the concentration of NO2 in the ambient atmosphere in Dongpu reservoir (latitude 31.89, longitude 117.20) in Hefei, Anhui Province, China from September 23rd to 30th, 2019. The comparison and correlation results of the simulation model of the neural network are shown in Fig.
We demonstrate a NO2 photoacoustic sensor system with a high-reflectivity mirror based on the low power blue diode laser at 403.56 nm. The high-reflectivity mirror enhances the power of the diode laser by increasing the number of reflections, resulting in the pool constant gain factor of 4.8 and a signal sensitivity gain factor of 6.4. Compared with that of a traditional photoacoustic sensor, the pool constant of the photoacoustic cell is improved from 300.24 (Pa⋅cm)/W to 1450.64 (Pa⋅cm)/W, and the signal sensitivity of the photoacoustic sensor is improved from 0.016 μV/ppb to 0.2562 μV/ppb. The properties of temperature and humidity of the new NO2 photoacoustic sensor are analyzed. The features of photoacoustic response and the drift of resonance frequency are also obtained and algorithm is corrected. The above research provides a new method and concept for further developing the NO2 photoacoustic sensors.
[1] | |
[2] | |
[3] | |
[4] | |
[5] | |
[6] | |
[7] | |
[8] | |
[9] | |
[10] | |
[11] | |
[12] | |
[13] | |
[14] | |
[15] | |
[16] | |
[17] | |
[18] | |
[19] | |
[20] | |
[21] | |
[22] | |
[23] | |
[24] | |
[25] | |
[26] | |
[27] | |
[28] | |
[29] | |
[30] | |
[31] | |
[32] | |
[33] | |
[34] | |
[35] | |
[36] |